TESLA CYBERTRUCK UP INVINCIBLE®
HD Roof Rack and V.1 MOLLE Panel
INSTALLATION GUIDE
ROOF RACK PARTS LIST
- TOP ROOF RAIL – Qty 1
- TOP MID ROOF RAIL – Qty 1
- BACK MID ROOF RAIL – Qty 1
- BACK ROOF RAIL – Qty 1
- DRIVER TOP RAIL SUPPORT BRACKET – Qty 1
- DRIVER TOP MID RAIL SUPPORT BRACKET – Qty 1
- DRIVER BACK MID RAIL SUPPORT BRACKET – Qty 1
- DRIVER BACK SUPPORT BRACKET – Qty 1
- PASSENGER TOP SUPPORT BRACKET – Qty 1
- PASSENGER TOP MID SUPPORT BRACKET – Qty 1
- PASSENGER BACK MID SUPPORT BRACKET – Qty 1
- PASSENGER BACK SUPPORT BRACKET – Qty 1
- TOP ROOF RAIL END PLATE – Qty 2
- TOP MID, BACK MID, AND BACK ROOF RAIL END PLATE – Qty 6
- NYLON LOCK NUT M6-1.0 – Qty 16
- NYLON LOCK NUT M8-1.25 – Qty 16
- 5MM ALLEN BOLT M8x1.25 – Qty 2
- M6 WASHER – Qty 16
- 5MM ALLEN BOLT M8x1.25 – Qty 32
- M8 WASHERS – Qty 50
MOLLE PANEL PARTS LIST
- DRIVER MOLLE PANEL – Qty 1
- PASSENGER MOLLE PANEL – Qty 1
- MOLLE PANEL SUPPORT BRACKETS – Qty 2
- 5MM ALLEN BOLT M8x1.25 – Qty 16
- M8 WASHERS – Qty 32
- NYLON LOCK NUT M8-1.25 – Qty 32
- 5MM ALLEN KEY
- 10MM SOCKET
- 13MM SOCKET
- MASKING TAPE
- PROTECTIVE TOWELS/BLANKETS
10mm M6 ROOF RAIL SUPPORT BRACKET LOCK NUTS – 12 ft/lb
13MM M8 ROOF RAIL SUPPORT BRACKET LOCK NUTS – 15 ft/lb
13MM M8 MOLLE PANEL SUPPORT BRACKET LOCK NUTS – 15 ft/lb
5MM M8 ROOF RAIL SUPPORT BRACKET END PLATE/MOLLE PANEL ALLEN BOLTS – 12 ft/lbs
By installing or using this product, you understand and agree with the following: If you do not agree, do not proceed with the installation and return this product within 30 days for a full refund of the purchase price from the company from which you have purchased it.
- I understand and agree that this product is intended to be installed for use on private roads and in jurisdictions where the use of this product is deemed legal by the local authorities. Furthermore, I understand and agree Unplugged Performance does not have any knowledge or control of regulations in my local jurisdiction, and it is up to me to determine if the product is acceptable for use with my vehicle.
- I understand that Unplugged Performance has done testing of this product on road and on closed racetracks but does not have the ability to test the vehicle for localized standards and regulations.
- I understand and agree that if the vehicle manufacturer determines that any Unplugged Performance products have contributed to a problem with the vehicle it may affect the vehicle’s warranty. Furthermore, I understand and agree that Unplugged Performance has no duty nor ability to be involved in internal manufacturer decisions.
- I understand and agree that if this product is given to an installer for installation on my vehicle, I have read and agreed with all the previous, even if I am not personally installing these parts on my vehicle. Furthermore, I understand and agree that this product should be installed by a trained professional that is familiar with both the vehicle as well as this product. Furthermore, I understand and agree that I and/or my chosen installer will follow the installation instructions carefully and dutifully test the vehicle post-installation in a safe and controlled environment to ensure proper operation.
- I understand and agree that by installing this product Unplugged Performance and all associated persons and entities as well as the vehicle manufacturer and all associated entities must be held harmless in the event of any suit, damages, or other legal action. Furthermore, I hereby release Unplugged Performance and any associated entities from any and all liability for any potential claim or claims.
If you do not agree with any of the above statements, you should return the product immediately. For more information please see our Terms and Conditions
First, open each factory anchor point cover to access the factory mounting points by pressing the inner side of the factory cover to access the M6 studs. There are 8 factory anchor point cover locations in total as shown below.
Using a 10mm socket, remove the factory nuts from factory anchor point 1,2,5, and 6. There is a total of 8 nuts that need to be removed from the vehicle.
Identify each support bracket’s intended mounting location. Each bracket should be packed with the relative roof rail, and are all location-specific. The Bracket shape is designed for follow the Cybertruck’s tapered body lines where the rear is wider than the front.
Using a 10mm socket, fasten 1 provided M6 lock nut and 1 provided M6 washer to each factory anchor point loosely to ensure that small adjustments to the support bracket location can be made to accommodate both the roof rack and molle panel placement.
Identify each roof rail, and place each roof rail onto its correlated support bracket. The roof rail length matches the taper of the factory mounting points, and therefore, the shortest bar is in the front, and the longest is in the rear. It is recommended that 2 people do this to prevent damage to the roof glass during the initial mounting process.
Place the rear roof rail onto the support brackets as shown below, and be sure to line up the mounting slots accordingly.
Once all mounting hardware securing the roof rails to the roof rail support brackets, apply final torque. Using a 5mm allen key and a 13mm socket to counter hold, torque each 13mm lock nut to and 5mm allen bolt to 15 ft/lbs.
Once all mounting brackets have been secured to the vehicle in their designated locations, apply final torque to each 10mm lock nut securing the support bracket to the factory anchor points. Torque to 10 ft/lbs.
Repeat Step 3 for all 4 roof rails.
First, identify the top end plate’s correlated mounting position. The top end plate is much taller than the other roof rail end plates. The rear 6 end plates are identical.
Using a 5mm allen key, fasten 1 M8x1.25 allen bolt, and 1 M8 washer to secure each end plate mounting point to the relative roof rail support bracket.Once the end plate hardware has been secured, apply final torque. Using a 5mm allen key, torque to 8 ft/lbs.
Once the end plate hardware has been secured, apply final torque. Using a 5mm allen key, torque to 8 ft/lbs.
**If you are installing Molle Panels, skip the remaining instructions in Step 3 and proceed to Step 4. If you are NOT installing Molle panels, proceed with the remaining instruction in Step 3 to complete your installation.**
Repeat all procedures from step 3 for the remaining 3 roof racks. Once completed, the installation of the UP INVINCIBLE® HD Roof Rack System is complete.
First, identify the driver and passenger side molle panels as these are location specific.
Next, using a 5mm allen key and a 13mm socket, fasten 1 provided 5mm M8x1.25 Allen bolt, 2 M8 washers, and 1 13mm M8x1.25 lock nut to 8 different points on the support bracket. We recommend spacing the fasteners for optimal weight distribution as shown. **Be sure to use the provided hardware with the molle panels for optimal bolt length.**
Next, tape off a corner of the backing tape cover so it can be removed once the molle panel is in place.
For this step, we recommend having 2 people present. One person will place the molle panel in position to ensure that the panel is properly aligned while the other person installs the 5mm Allen bolts by hand. Be sure to loosely fit all 6 bolts before applying final torque. If any bolts do not line up, remove the Molle panel to make adjustments to the roof rail support brackets by loosening the 10mm nuts to allow for support bracket relocation and proper panel alignment.
Using a 5mm Allen key, fasten a 5mm Allen bolt in each mounting point (6 total per molle panel) to secure the molle panel to the roof rail support brackets and torque to 8 ft/lbs.
Once the hardware has been torqued accordingly, you will have one person lightly lift the molle panel away and downward from the vehicle to allow for clearance. The other person will pull the tape backing off.
Once the tape backing has been removed, you will lightly pull the molle panel down and away from the vehicle in a slow sweeping motion until the support bracket is pressed against the rear quarter panel.
Repeat step 5 and 6 for the other MOLLE panel to complete your installation.
Congratulations! Your Installation is complete!
If you have any outstanding questions or concerns, please reach out to the Customer Support by calling 213-279-7420, OR by emailing us at support@unpluggedperformance.com with your name, order number, and context regarding your concerns.
