TESLA CYBERTRUCK UP INVINCIBLE®

HD Swing Arm MOLLE Panel & Latch Set

INSTALLATION GUIDE

• MOLLE Swing Arm – Qty 1
• MOLLE Swing Arm Support Bracket – Qty 1
• Locking Latch Module – Qty 1
• Keys for Locking Latch – Qty 1
• Latch Striker – Qty 1
• 15MM M10x1.5 Bolts – Qty 4
• M10 Locking Washer – Qty 4
• 10MM M6x1.25 Locking Nuts – Qty 4
• 10MM M6x1.25 Nuts – Qty 2
• M6 Bump Stop – Qty 2
• Upper aluminum sleeve – Qty 1
• Lower aluminum sleeve – Qty 1
• 10MM allen M12x1.75x150mm (35mm) partial thread – Qty 1
• 19MM M12x1.75 nylock nut – Qty 1

• 10mm end wrench
• 10mm deep socket
• 15mm socket
• 19mm socket
• 5mm allen socket
• 10mm allen socket
• Torque wrench

• Please see individual steps for torque specs.

By installing or using this product, you understand and agree with the following: If you do not agree, do not proceed with the installation and return this product within 30 days for a full refund of the purchase price from the company from which you have purchased it.

• I understand and agree that this product is intended to be installed for use on private roads and in jurisdictions where the use of this product is deemed legal by the local authorities. Furthermore, I understand and agree Unplugged Performance does not have any knowledge or control of regulations in my local jurisdiction, and it is up to me to determine if the product is acceptable for use with my vehicle.
• I understand that Unplugged Performance has done testing of this product on road and on closed racetracks but does not have the ability to test the vehicle for localized standards and regulations.
• I understand and agree that if the vehicle manufacturer determines that any Unplugged Performance products have contributed to a problem with the vehicle it may affect the vehicle’s warranty. Furthermore, I understand and agree that Unplugged Performance has no duty nor ability to be involved in internal manufacturer decisions.
• I understand and agree that if this product is given to an installer for installation on my vehicle, I have read and agreed with all the previous, even if I am not personally installing these parts on my vehicle. Furthermore, I understand and agree that this product should be installed by a trained professional that is familiar with both the vehicle as well as this product. Furthermore, I understand and agree that I and/or my chosen installer will follow the installation instructions carefully and dutifully test the vehicle post-installation in a safe and controlled environment to ensure proper operation.
• I understand and agree that by installing this product Unplugged Performance and all associated persons and entities as well as the vehicle manufacturer and all associated entities must be held harmless in the event of any suit, damages, or other legal action. Furthermore, I hereby release Unplugged Performance and any associated entities from any and all liability for any potential claim or claims.

If you do not agree with any of the above statements, you should return the product immediately. For more information please see our Terms and Conditions. 

Using a 15mm socket, fasten 4 M10x1.5x30mm bolts to secure each swing arm bracket to the UP INVINCIBLE rear bumper in the following orientation.

Using a 15mm socket and a torque wrench, torque all 4 bolts to 30 ft/lbs.

Next, proceed to assemble your MOLLE swing arm. First, fasten 2 provided M6 bump stops and 2 10MM M6x1.25 nuts on each upper corner of the MOLLE swing arm as shown below.

Next, proceed to install the latch onto the swing arm. Using a 10mm socket, 10mm end wrench, and a torque wrench, fasten 4 10MM M6x1.25 nuts to secure the latch to the MOLLE swing arm as shown below. Note that 2 nuts require an end wrench to access while the other 2 can be fastened with a traditional deep socket. Torque to 10 ft/lbs.

Once the latch is installed, proceed to install the MOLLE swing arm onto the MOLLE swing arm mounting bracket. Lift the MOLLE swing arm into the bracket as shown below.

With the swing arm in position, insert the following hardware to fasten the MOLLE swing arm to the bracket. Start by inserting the threaded aluminium sleeve on the bottom, and the non-threaded aluminum insert into the top. Using a 10mm allen key, fasten the provided M12 bolt through the upper aluminium sleeve, to the lower threaded aluminium sleeve. The torque on this bolt directly reflects how much force is required to move the swing arm through the intended range of motion.

Once the swing arm pivot friction has been set, using a 19mm socket and a 10mm allen key to counterhold, fasten a supplied 19mm lock nut underneath the threaded aluminium sleeves to retain your pivot friction setting.

Once the swing arm has been installed, proceed to install the latch stroker. Using a 5mm allen key, loosely fasten 4 bolts to secure the latch striker to the vehicle. Note that the striker bracket is slotted to allow for fine tune adjustments and optimal placement.

Before applying final torque, test the swing arm latch engagement with the striker, and adjust the striker position as needed.

Finally, using a 5mm allen socket and torque wrench, torque all 4 striker bolts to 17ft/lbs.

Note: If you plan to use FSD, you may experience some warnings when the swing arm and or 5th wheel carrier is added to the UP INVINCIBLE rear bumper. If this occurs, you can place the vehicle in service mode, and recalibrate the cameras. This has proven to reduce proximity errors when using FSD successfully with swing arms and or 5th wheel carriers added to the UP INVINCIBLE rear bumper.